Corpus Christi 361.882.3444Kenedy 830.400.8310
sales@mriautomation.comLinkedIn
MRI Automation
Home / Tech Tips / SCADA Telemetry for Remote Oilfield Sites: What Actually Works in South Texas
Remote monitoring

SCADA Telemetry for Remote Oilfield Sites: What Actually Works in South Texas

MRI Automation · November 2026 · 5 min read

Your SCADA system is only as good as the data that reaches the office. A well-built RTU on a remote Eagle Ford pad does nothing for you if the telemetry link drops every afternoon.

The worst part is that a dropped link does not look like an outage. The screen keeps showing the last good reading. The pad has been dark for six hours and nobody knows.

When telemetry keeps failing on remote pads, the SCADA platform is rarely the problem. The problem is the communication path underneath it, and whether anyone designed that path for the site it actually serves.

Why SCADA telemetry fails on remote South Texas pads

We see three causes over and over. None of them are SCADA platform problems.

The comms path was never checked at the site

A cellular modem gets specified because the coverage map shows service. Then it goes on a pad twelve miles from the nearest tower, behind a low rise that blocks the signal. It connects in the morning and drops in the afternoon when the tower is busy. The SCADA system takes the blame. The real issue is that nobody tested the signal at the pad before the modem was installed.

The RTU polls faster than the link can carry

Many SCADA platforms ship with fast polling settings. On a wired connection or a strong cell signal, that is fine. On a weak radio path or a busy rural tower, fast polling floods the link. Data arrives late, arrives incomplete, or stops. The HMI shows stale values, and the operations team stops trusting the screen.

The antenna was mounted for convenience, not the environment

An antenna inside a metal enclosure, or mounted low on the sunny side of the cabinet, is a signal problem and a heat problem at once. In August, the inside of an enclosure can reach 140°F. The link weakens and drops during the hottest part of the day, which is exactly when equipment is under the most stress and monitoring matters most.

What a well-designed telemetry path does differently

Reliable telemetry starts at the site, not in the catalog. We drive to the pad and check the signal before we specify the radio. We test at the worst time of day, because that is when the telemetry matters most. Three design choices follow from that visit.

Match the comms path to the site

Cellular is the default because it is familiar and inexpensive. But cell service in rural South Texas is not cell service in Houston. Terrain, tower load, and distance all affect it.

  • Cellular works well where the signal tests strong at the pad.
  • Licensed or unlicensed radio gives you a dedicated path that does not compete with every phone on the tower. A 900 MHz link can reach from half a mile up to 60 miles, depending on antenna height and terrain.
  • Wired telemetry removes the wireless question entirely when the pad is close to existing conduit. On a single remote pad, though, trenching often costs more than the whole radio system.

The right answer is whatever the site actually supports. Our telemetry services cover both wired and wireless paths.

Poll at a rate the link can carry

Set the polling interval to what the connection can reliably deliver, and buffer data at the RTU. If the link drops for thirty seconds and recovers, the buffered data fills back in and the HMI shows a continuous record. If the polling rate is faster than the link can handle, that data is simply lost. Slowing the poll is not a downgrade. It is the difference between a full record and gaps.

Mount the antenna for the worst week of the year

Use an external antenna rated for the climate, mounted above the enclosure, with lightning protection on the cable. The setup that survives a South Texas August also holds up through a winter freeze. The panel matters too: a well-built control panel with rated terminations, on properly sized electrical, keeps the radio and RTU running when conditions are at their worst.

The data link is part of the system

Your control panel can be built right. Your electrical work can be sized correctly. Your RTUs can be good hardware. If the telemetry layer was not designed for the site, you are still running blind on your remote pads.

Operators who trust their SCADA data did three things. They tested the signal at the pad, matched the polling rate to the connection, and mounted the antenna for the conditions. They also have a local team that can reach the site when a link drops, because eventually every link does.

That is how we approach SCADA telemetry at MRI Automation. Our crews in Kenedy and Corpus Christi design telemetry for each site, wired or wireless, and come back when it needs attention.

Have pads where the SCADA keeps going quiet? Request a telemetry site survey. We will check your signal, polling, and antenna setup and give you a plain list of what to fix. Or call our team at 361.882.3444.

Frequently asked questions

What is the best communication method for SCADA telemetry on remote South Texas pads?

It depends on the site. Cellular is the most common choice, but rural coverage is inconsistent and busy towers cause data gaps. Where cellular is weak, a licensed or unlicensed radio link gives you a dedicated path. Where wired infrastructure already reaches the pad, wired telemetry avoids wireless issues entirely. The only way to know is to test the signal at the pad.

How do I prevent SCADA data gaps on remote wellpads?

Match the polling rate to what the connection can carry, and turn on local buffering at the RTU so short dropouts fill back in. Mount the antenna outside the enclosure with lightning protection. And work with a team close enough to reach the site quickly when a link does drop.

Does MRI Automation support SCADA telemetry in the Eagle Ford?

Yes. MRI Automation has offices in Kenedy and Corpus Christi, with field crews who live and work in the Eagle Ford. We test signal at the pad, design wired and wireless telemetry paths, integrate RTUs and HMIs, and provide on-site service when a link drops.

Talk to someone who's been on the pad

Request a Site Survey

Related service

Telemetry